Help
What do I need?
- An OBD-II adapter with an ELM327 chip (or compatible, such as OBDLink or vLinker). Tested ones: "Connect" → "Which adapters work".
- A car with an OBD-II port: petrol cars from 2001, diesels from 2004 (in Europe), all cars from 1996 in the US. The port is usually under the steering wheel on the left.
- The ignition on. The engine need not run, but live data and tests work best with it running.
Without an account or internet everything works except AI analysis and sync.
How do I connect a Bluetooth adapter on Android?
- Plug the adapter into the OBD-II port and turn the ignition on — its light should come on.
- Pair a classic Bluetooth adapter ("OBDII", "V-LINK") first in Android settings → Bluetooth. The PIN is usually 1234 or 0000.
- In the app: "Connect" → Bluetooth. Adapter-like devices come first and the adapter is picked for you. Tap "Connect".
- Bluetooth LE adapters need no pairing — the search finds them.
If the app asks for "Nearby devices" — allow it: without it Android shows no Bluetooth devices.
Which COM port do I choose on Windows?
- Pair the adapter first: Windows Settings → Bluetooth & devices → Add device. The PIN is 1234 or 0000.
- Windows creates two COM ports for the adapter: outgoing and incoming. Only the outgoing one works — the app shows it first with the adapter's name ("COM5 — OBDII") and marks the other as "incoming port", not selectable.
- A USB cable (FTDI, CH340) shows up as a COM port too.
- If the adapter has no power or is too far, Windows waits for it for up to a minute. The app shows how long it has waited — it has not frozen.
- Reconnecting to the same port takes a few seconds' pause: without it Windows hangs for a minute.
Keyboard shortcuts are listed in "Settings".
Why can't my iPhone see the adapter?
iPhone works only with Bluetooth LE and Wi-Fi adapters. The most common cheap "OBDII" adapters (ELM327 v1.5) use classic Bluetooth — an iPhone cannot see them, and pairing in iOS settings will not help. You need a BLE adapter (such as vLinker MC-IOS or Vgate iCar Pro BLE) or a Wi-Fi one.
If your adapter is BLE but not in the list:
- check that Pidkapot may use Bluetooth: Settings → Pidkapot → Bluetooth;
- turn the ignition on — without power the adapter is invisible;
- close other diagnostic apps: a BLE adapter talks to one app at a time.
How do I connect a Wi-Fi adapter?
- Turn the ignition on and join the adapter's Wi-Fi network on your phone or laptop (usually WIFI_OBDII, no password).
- In the app: "Connect" → Wi-Fi. The default address is 192.168.0.10:35000; if the adapter's manual says otherwise, type it in.
- On iPhone allow "Local Network" access when the app asks.
While you are on the adapter's network there may be no internet: AI analysis waits in a queue and runs by itself when the internet is back.
"The adapter does not respond" — what now?
- Unplug the adapter for a few seconds and plug it back in.
- Check that it has power (the light is on). In some cars the port is powered only with the ignition on.
- Close other apps that may hold the adapter.
- Cheap clones sometimes lack certain commands — the app skips them and learns each model's quirks from the knowledge base.
The connection log ("Connect" → "Connection log") shows the step where connecting stopped. You can send it to us via "Report a problem".
"The car does not answer over OBD-II" — what does it mean?
The adapter works, but the engine control unit did not answer.
- Turn the ignition on (ON position). If it is already on, try starting the engine.
- Old cars (before 2001 in Europe) often use factory protocols instead of OBD-II — the app does not support them.
- Some cars stop talking a few minutes after the ignition is turned on without starting the engine — turn it on again.
How do I read trouble codes?
- The first letter is the system: P — engine and transmission, C — chassis, B — body, U — communication between units.
- Confirmed codes light the "Check Engine" lamp. Pending — the unit saw the problem once and keeps watching. Permanent codes survive clearing — they go away only after the car checks by itself that the problem is fixed.
- Next to each code: what it means, whether you can drive, the likely causes and checks — the simplest first.
- The freeze frame shows the sensors at the moment the code appeared: rpm, temperature, speed.
How do I read the AI report?
- Urgency light: 🟢 fine to drive, plan the repair; 🟡 drive carefully and check soon; 🔴 do not drive — risk of engine damage or to safety.
- Problems — what is likely wrong, with evidence: which codes, readings or tests point to it.
- Checks are ordered from the cheapest. Start with the first.
- Missing data — what would firm up the verdict (for example, a warm-up test or live data with the engine running).
The report does not replace a garage. Critical codes from the knowledge base always give 🔴, whatever the AI "thinks". Rate the report with 👍 / 👎 below it — it helps us improve it.
When can I clear the codes?
Only with the engine off, the ignition on and the car standing still. The app checks this itself. Clearing also erases the freeze frame and the self-test results — the car will run them again over several drives. If the cause is not fixed, the code comes back.
Some codes must not be cleared (for example, P1326 on Theta II engines) — the app explains why and advises a dealer visit.
What are live data and norms?
"Live" shows the sensors in real time: rpm, temperature, fuel trims, voltage and more. For known models the norm for your engine is shown next to each value; readings out of the norm are highlighted. You can record a trip and see the graphs and fuel use.
The in-car mode shows four large readings on a dark screen that stays on and beeps on a warning. Complex actions are locked while driving.
My account and data
- Without an account everything stays on this device only.
- An account is needed for AI analysis, sync between devices and the web cabinet. Sign in with an emailed code (on iPhone also with Apple).
- Data reaches our server in the EU only after you accept the privacy policy.
- "Settings" → "Account": export all your data (JSON or CSV) and delete the account with all its data.
How do I report a problem?
"Settings" → "Report a problem". Describe what happened and, for a connection problem, attach the connection log — it holds the adapter's type and name and the result of each step, no VIN and no adapter address. An account is needed so that we can answer you.